Schneider Electric Smart-UPS On-Line

The Smart UPS On-Line UPS with double conversion of energy is intended for uninterrupted power of the equipment with a high density of power: servers, networks of a voice communication and data transmission, medical laboratories and small plants.

The Smart UPS On-Line UPS with a power from 1 to 20 kVA has the universal vertical/rack body. In rack option occupies from 2 to 12 U. Recently provided 15 and 20 kVA models allow to connect a power-intensive blade servers and racks with the high density of power. When systems, crucial for business, need not in minutes, and in hours of independent operation, the Smart UPS On-Line UPS can be completed with the corresponding battery packs providing increased requirements by the time of independent operation. Software of management of PowerChute supports safe automatic completion of work of network operating systems. All 5 kVA models are completed with the built-in payment of network management also above (an option for models with power less than 5 kVA). All line of the Smart UPS On-Line UPS is of special interest for exacting customers to whom such characteristics as very broad range of input voltage, extremely exact stabilization of voltage output, frequency fixing, the built-in bypass and correction of entrance electrical power factor are important.

Advantages

• Possibility of adaptation
• The updated microprograms in a flash memory - Remote installation of versions of a firmware through FTP.
• The external batteries connected by the principle of the Plug and Play - Providing the protected equipment with sinusoidal uninterrupted power in the course of connection to the UPS of additional accumulators.
• Transformed between configurations in the tower / chassis body for installation to hardware racks - Protection of initial investments into the UPS upon transition from the UPS in the vertical body to rack UPSes.

Readiness

• Automatic internal bypass - in case of an overload or fault of the UPS of loading will switch to a power supply from the power supply network.
• Automatic restart of payloads after switching off of the UPS - Automatic start of the connected equipment after recovery of network power supply.
• Replacement of batteries during operation UPS - Providing the protected equipment with net sinusoidal uninterrupted power when replacing rechargeable batteries.
• Intellectual control of batteries - the Maximum increase in efficiency of the battery, increase in term of its service and reliability at the expense of exact intellectual charging.
• The scalability on operating time from accumulators - If necessary allows to increase battery life quickly.

Administriruyemost

• Compatibly to InfraStruXure Manager - the Possibility of centralized operation using APC InfraStruXure Manager.
• LED status lights - Visual indicators quickly give an idea of a status of the device and power supply.
• Management of the UPS through a local network - A possibility of remote control of the UPS on network.
• Connection through a serial port is Management of the UPS through a serial port.
• SmartSlot connector - Application of payments of management allows to modify a set of opportunities of the UPS.

Protection

• Start of the UPS in the absence of electricity in network ("cold start") - Ensuring a time power supply from batteries in case of a break of giving of network power supply.
• Adjustment of frequency and tension - Increase in operational readiness of systems due to correction of frequency deviations and tension from regulation without use of batteries.
• Compatibly to reserve generators - Providing the protected equipment with net sinusoidal uninterrupted power during the work from the generator.
• Correction of electrical power factor on an input is Minimization of cost of installation due to use of generators of smaller power and use of cables of smaller section.
• Conditioning of a power supply is Protection of loadings against the pulse overvoltage including caused by lightning discharges and other powerful impacts on an electric power supply system.

Maintainability

• Sound signals - the Notification on changes of network power supply and operating conditions of the UPS.
• The built-in automatic test of operability of the UPS - Regular self-diagnostics of batteries allows to detect the battery which is subject to replacement timely.
• The non-availability notice of connection with the battery - in case of unavailability of the battery for providing back power supply moves the precautionary message.
• The notification on the predicted failures - Advance identification of possible failures allows to execute anticipatory replacement of components.
• The batteries replaced by the user - Increase in operation capabilities of the device.

2019: SRT1000RMXLI, SRT1000RMXLI-NC, SRT1500RMXLI и SRT1500RMXLI-NC

On November 19, 2019 the Schneider Electric company provided models of uninterruptible power supply units of APC Smart UPS Online of a line of SRT with lead-acid batteries. In total the line of SRT was replenished with 4 SRT1000RMXLI, SRT1000RMXLI-NC, SRT1500RMXLI, SRT1500RMXLI-NC models on 1000 and 1500VA respectively. The SRT models with a power of 1000BA succeeded the analogs from a line of SURT (SURT1000RMXLI and SURT1000RMXLI-NC). Devices are available as with the network interface card (-NC), and without it.

According to the company, devices of a series of APC Smart UPS Online SRT are the UPS with double conversion and a net sinusoid at the exit. Power Factor of devices is equal to 1. At the time of connection to the UPS of external accumulators, a system will define it in the automatic mode, and at the arisen need of the device will be able to work without loss of efficiency, even directly from network without the built-in battery. It will allow to make replacement of the accumulator even at its breakdown, trouble-free in a power supply and functioning of all system.

The sizes of the provided UPSes of the SRT series are — 85 x 432 x 505 mm, and weight does not exceed 29.6 kg. Tolerance range of temperature for normal operation of devices of a series is from 0 to 40 °C. Battery life depends on existence of additional accumulators and their quantity. About 10 add-on external battery modules are greatest possible to connect. In the absence of external batteries and permanent power of the device will be able independently to function within about 5 minutes. In total it is possible to connect up to 10 accumulator banks that will allow to increase operating time till three and a half o'clock.

In these models the regime of economy which allows to support high efficiency without weakening of protection is available, but at the same time to spend less energy due to redistribution of load of a bypass. All necessary information from the device, including the notification on need to undergo maintenance, is transferred in real time to the built-in LCD display. The producer gives a three-year guarantee for SRT series devices that together with other parameters does models of this series by an optimal solution for offices and server rooms.

2018

ИБП SRV6KRIL, SRV10KRIL, SRV1KIL, SRV3KIL, SRV6KIL и SRV10KIL

On September 04, 2018 the Schneider Electric company announced expansion of the range of uninterruptible power supply units of APC Easy UPS On-Line of the SRV series the additional models supporting connection to four external rechargeable batteries. Due to this feature the possibility of significant increase in battery life of the UPS appears. The possibility of adding of external rechargeable batteries is provided in the SRV6KRIL, SRV10KRIL, SRV1KIL, SRV3KIL, SRV6KIL and SRV10KIL UPS models. All listed UPSes belong to srednetsenovy range. Other important feature is the high power factor in loading which in the 6000 VA models and 1000 BA reaches value 1, and in other provided models is equal to 0.8.

The biggest battery life from the provided UPSes shows SRV2KL. Using only the built-in battery battery life at an overall load is 22 minutes, and when adding four more external rechargeable batteries this indicator increases up to 159 minutes. These models in the SRV series supporting connection of external rechargeable batteries differ in letter L on the end of the name. Are provided as the models intended for rack-mounting and models in the Tower body.

Models with powers of 6000 VA and 10000 BA have also other important design feature — they consist of two separated elements: UPS and main battery. Thanks to such solution replacement of the rechargeable battery at planned maintenance becomes simpler.

In all provided models "hot" replacement of external rechargeable batteries is supported. For increase in safety of such replacement each of batteries is supplied with the built-in circuit breaker.

SRV6KRIL, SRV10KRIL, SRV1KIL, SRV2KIL, SRV3KIL, SRV6KIL and SRV10KIL UPSes are intended for ensuring smooth operation of crucial elements of engineering infrastructure. The possibility of accumulation of battery life without replacement of the UPS, only connection of additional accumulators, is especially relevant for dynamically developing productions as it allows to reduce initial investments in the equipment.

Especially clear advantage of the UPS of the APC Easy UPS On-Line SRV series are shown when using where at the limited budget it is required to have a large supply on battery life: in medical institutions, data centers, telecommunication companies, state bodies, difficult productions, etc. High reliability of back supply is provided with a number of construction features of the UPS, including function of intellectual control of accumulators with temperature compensation which prolongs service life of batteries Anna Miziyeva, business development manager of single-phase products of division of IT Division of Schneider Electric company.

Universal APC Easy UPS On-Line UPSes of the SRV series

On March 29, 2018 the Schneider Electric company provided universal uninterruptible power supply units of APC Easy UPS On-Line of the SRV series. Three UPS models, SRV3KI, SRV6KI and SRV10KI which are a part of a line have a capacity 3000 BA (2400 W), 6000 BA (6000 W) and 10000 BA (10000 W). In the second quarter 2018 two more UPSes of this series will be released: SPV1KI and SRV2KI, 1000 and 2000 VA respectively. All models of a line enter in srednetsenovy a segment.

SRV series APC Easy UPS On-Line UPS

According to representatives of Schneider Electric company, the APC Easy UPS On-Line UPS are intended for ensuring smooth operation of crucial elements of engineering infrastructure of the company: network equipment, data processing centers, VOIP and VSAT devices, systems of visualization and monitoring and also various industrial complexes.

APC Easy UPS On-Line UPSes of the SRV series are designed for operation in difficult conditions — the broad range of input voltage (from 160 V to 280 V - SRV3KI and from 176 V to 300 V – SRV6KI, SRV10KI) allows them to carry out the tasks at an unstable power supply. The senior models (SRV6KI and SRV10KI) are equipped with the EPO function which allows to disconnect power supply urgently.

APC Easy UPS On-Line UPS of the SRV series (SRV6KI, SRV10KI)

Devices of a line have high power factor — from 0.8 for younger models up to 1 for seniors. At the same time correction of coefficient of input power makes 0.95 that allows to cut down operating costs, using the smaller number of generators and cables, and function of intellectual control of accumulators with temperature compensation prolongs service life of batteries and increases reliability of a system of back supply. Also UPSes are equipped with switches for overvoltage protection that excludes potential damages its component, the producer noted.

UPS operating time under an overall load is from two to four minutes, and the recharge up to 90% of capacity borrows from three to four hours.

Rather small sizes of devices do them insensitive to the location: they can be set both at small office, and in the production premises.

All devices of a series use technology of double conversion (On-Line). This solution allows to provide ideal voltage output at almost any malfunctions in the power supply network and to achieve lack of a gap when switching from the normal mode in autonomous and back, guaranteeing lack of transition processes, noted in Schneider Electric.

APC Easy UPS On-Line devices of the SRV series are simple in installation and are convenient in operation. Control of their status can be exercised by means of the LCD display, and the sound signal will notify on change of power of the power supply network and an operation mode of the UPS. Control of the equipment can be exercised through a serial port.

Single-phase UPSes with SRTL series li-ion cells

On March 6, 2018 the Schneider Electric company provided the Smart UPS Online UPS models on the 1 kVA and 15 kVA Li-ion batteries. In each power there is two an option of execution of model with the preset network interface card (SRTL1000RMXLI-NC and SRTL1500RMXLI-NC) and without (SRTL1000RMXLI and SRTL1500RMXLI). The given APC Smart UPS Online UPSes are the first serial on-line single-phase APC devices of low power with Li-ion rechargeable batteries (joint stock bank) brought to the Russian market.

The UPS models are constructed according to the scheme On-Line with double conversion. Devices are held for use where high reliability and long operating time of the equipment at breaks in power supply are required: on industrial enterprises of the average size, in telecommunications, in medical laboratories, when processing crucial business information. The main innovation applied in these devices is use of Li-ion (Li-Ion) accumulators instead of traditional for the UPS lead-acid.

Smart UPS Online (2018) UPS

In comparison with traditional joint stock banks treat advantages of Li-Ion of accumulators: the compact sizes and smaller weight, up to 4 times the high speed of charging, twice bigger service life of the rechargeable battery (up to 10 years), an opportunity for work at a temperature up to +40 °C without significant deterioration in parameters. As result, the total cost of housekeeping overheads fell by 35% in comparison with similar models with other type of accumulators. Application of Li-Ion of accumulators lies in line with a current trend of temperature increase in halls of data processing centers for economy of energy due to less intensive cooling.

The APC Smart UPS SRLT1000RMXLI UPS is expected loading with a rated power of 900 W / 1000 BA, and APC Smart UPS SRLT1500RMXLI — 1350 W / 1000 BA. The sizes (without accumulators) at both models identical — 85 x 432 x 587 mm, weight (without accumulators) too identical — 13.7 kg. UPSes can be installed as in a rack, and to be used out of it – in floor execution. Operation both in horizontal, and in vertical position is allowed.

The rechargeable battery is executed in the form of the separate removable block. Its sizes are 85 x 432 x 510 mm, weight — 12 kg. Operating time from the rechargeable battery is 32 min. at load of 900 W for APC Smart UPS SRLT1000RMXLI and 19 min. at load of 1350 W for APC Smart UPS SRLT1500RMXLI. This time can be increased if to add add-on units of accumulators. At both models it is possible to install up to 5 such blocks, including regular. Respectively, it is possible to increase operating time to 5 times.

2017: The line of Smart UPS On-Line was replenished with budget models

In May, 2017 Schneider Electric updated a line of uninterruptible power supply units of Smart UPS On-Line. Since March, 2017 in Russia sales of models of a mid-price segment of the SRC series some of which it is up to 40% more profitable than devices of the senior SRT co series similar power (volt-ampere) characteristics started.

Smart UPS On-Line UPSes are constructed on technology of double conversion and differ in high power density. They are intended for protection of power supply of servers, network equipment, medical and scientific laboratories and also low-power plants. SRC series models in floor execution with a power range from 1 to 10 kVA are available to customers.

From the senior SRT series new UPSes adopted all basic functions: capability to work with the broad range of input voltage, tough adjustment of voltage output, frequency regulation, an internal bypass and correction of a factor of force of an input signal. For Smart UPS On-Line of the SRC series with a power from 3 kVA the connectivity of external batteries is available to increase in battery life.

Unattended hermetic lead-acid batteries with thickened electrolyte and protection against leaks can be replaced by the user. Exact intellectual charging increases their efficiency and prolongs life up to 3-5 years. The alphanumeric display displays system parameters and abnormal messages, besides, the UPS can be managed far off via the serial interface, USB port or through network after installation of a special payment. Correction of electrical power factor on an input allows to minimize costs for installation due to use of generators of smaller power and use of cables of smaller section.

2015: SRT series smart UPS On-Line

On December 21, 2015 the division of IT Business of Schneider Electric company announced release of uninterruptible power supply units of Smart UPS On-Line of the SRT series with a power of 2.2 and 3 kVA - SRT2200XLI and SRT3000XLI.

APC Smart UPS SRT2000XLI (2015)

APC Smart UPS SRT2200XLI is a back view (2015)

APC Smart UPS SRT2200XLI - with battery (2015)

Devices have the universal body with a possibility of vertical installation or installation in a rack. Work on technology of double conversion that allows to provide protection of power supply of servers, the equipment of data networks, medical laboratories and the industrial systems.

The efficiency of Smart UPS On-Line of the SRT series exceeds 97% at coefficient of power output 0.9. Among other functional features - the interactive user interface, an automatic internal bypass, intellectual control of batteries and also a possibility of "hot swap" of batteries by the user and connections of external accumulators in the Plug and Play mode. UPSes are equipped with the SmartSlot connector, support an ability to manage and software updatings through network and are compatible to InfraStruxure Manager.

Data of automatic self-diagnostics and the notification on the predicted failures are displayed by LED indicators that simplifies operation of the UPS. Devices are on sale in the vertical body, but can be rack-mounted.

Requirements to energy consumption and availability to the IT equipment increase. Clients need the UPS capable to guarantee excellent quality of a power supply and efficiency in flexible construction that provides easy installation, operation and service practically in any environment. Crucial business systems require battery life, measured for hours, but not minutes. As a result, the UPS of the Smart UPS On-Line series can be configured with add-on battery packs for observance of requirements of the customer. Svyatogor Gavrilenko, the head on work with retail partners of division of IT Business of Schneider Electric company

The three-year limited warranty of the producer, term of warranty service of batteries extends 2 years to the UPS.

2014: New generation of Smart UPS On-Line

On June 17, 2014 the Schneider Electric company provided new generation of single-phase UPSes with the electrical power factor equal to unit: line of the APC by Schneider Electric Smart UPS On-Line UPS of 5-10 kVA.

All models, with power from 6 to 10 kVA, having electrical power factor 1.0, provide maksimalnkyu power in watts (W) equal to the stated power in the volt-amperes (VA). The exception is made by the 5 kVA model expected an indicator 0.9.

Advantages

• New Smarts UPS On-Line show high rates of power and quality of power supply at the compact sizes.
• The possibility of installation in a rack, installations separately, helps to unroll, operate and service effectively the UPS in any environment.
• All models of a new line are equipped with the built-in payments of network management, the LCD screen with an opportunity to change source operation parameters without special software, the managed groups of sockets and the built-in mechanism of forecasting of the recommended date of replacement of batteries (Predictive Battery Replacement).

New uninterruptible power supply units of APC Smart UPS On-Line work on topology of double conversion and are suitable for a broad spectrum of applications: from switching nodes and server to the remote offices and plants requiring the protected power supply. Devices of the high level of readiness in which the inverter continuously regulates output parameters can be used to protection of the equipment intolerant of the slightest voltage drops or frequency deviations (for example, devices with not switch mode power supplies, widespread on production and in management systems).

Capability of the majority of computing and network devices without effects to maintain short interruptions in power supply (20 ms and more) allows operation of the Smart UPS On-Line UPS in the ecomode when double conversion is not executed, and the level of efficiency reaches 97%. Electricity consumption and expenses on its payment decreases, heat production decreases that positively affects service life of key components, such as batteries.